NXT Settings - Was ist das? - what´s that? - AccuRender nXt2024-03-28T08:33:42Zhttp://accurender.ning.com/forum/topics/nxt-settings-was-ist-das-what-s-that?feed=yes&xn_auth=noHi Roy,
is it possibel to se…tag:accurender.ning.com,2016-09-21:6293855:Comment:1236512016-09-21T07:35:15.377ZJudith Kleinhttp://accurender.ning.com/profile/JudithKlein
<p>Hi Roy,</p>
<p></p>
<p>is it possibel to send me the file in Version 2007?</p>
<p>Best regards, Judith.</p>
<p>Hi Roy,</p>
<p></p>
<p>is it possibel to send me the file in Version 2007?</p>
<p>Best regards, Judith.</p> I've looked pretty closely an…tag:accurender.ning.com,2016-09-20:6293855:Comment:1234852016-09-20T17:32:14.610ZRoy Hirshkowitzhttp://accurender.ning.com/profile/RoyHirshkowitz
<p>I've looked pretty closely and haven't been able to find anything wrong with the drawings or the algorithms. It's definitely having trouble with the lighting in this model-- I did the following:</p>
<ol>
<li>Changed the beam angle on the lights to 10 degrees. I had to explode the light blocks to do this.</li>
<li>Set the lighting to studio mode using the rnl_probe hdr.</li>
<li>Set the Brightness to 0.2.</li>
<li>Unchecked the Gather switch for the ground (floor) objects and made the large…</li>
</ol>
<p>I've looked pretty closely and haven't been able to find anything wrong with the drawings or the algorithms. It's definitely having trouble with the lighting in this model-- I did the following:</p>
<ol>
<li>Changed the beam angle on the lights to 10 degrees. I had to explode the light blocks to do this.</li>
<li>Set the lighting to studio mode using the rnl_probe hdr.</li>
<li>Set the Brightness to 0.2.</li>
<li>Unchecked the Gather switch for the ground (floor) objects and made the large circular one a little smaller.</li>
</ol>
<p>That's about it, I think. All of the other values were left alone, including the output of each light. I'll send you the updated drawing.</p>
<p><a href="http://storage.ning.com/topology/rest/1.0/file/get/55262875?profile=original" target="_self"><img src="http://storage.ning.com/topology/rest/1.0/file/get/55262875?profile=original" width="700" class="align-full"/></a></p>
<p><a href="http://storage.ning.com/topology/rest/1.0/file/get/55262795?profile=original" target="_self"><img src="http://storage.ning.com/topology/rest/1.0/file/get/55262795?profile=original" width="700" class="align-full"/></a></p> Da bin ich mal gespannt. wa d…tag:accurender.ning.com,2016-09-17:6293855:Comment:1235502016-09-17T15:06:52.006ZAlfons Akamphttp://accurender.ning.com/profile/AlfonsAkamp
<p>Da bin ich mal gespannt. wa da heraus kommt.</p>
<p>Da bin ich mal gespannt. wa da heraus kommt.</p> It's not a units issue, they'…tag:accurender.ning.com,2016-09-16:6293855:Comment:1235492016-09-16T20:58:21.212ZRoy Hirshkowitzhttp://accurender.ning.com/profile/RoyHirshkowitz
<p>It's not a units issue, they're ok. I'll let you know soon what I've found.</p>
<p>It's not a units issue, they're ok. I'll let you know soon what I've found.</p> Hi Thorsten,
Ich habe DDUNITS…tag:accurender.ning.com,2016-09-16:6293855:Comment:1238092016-09-16T17:56:10.305ZJudith Kleinhttp://accurender.ning.com/profile/JudithKlein
<p>Hi Thorsten,</p>
<p>Ich habe DDUNITS eingegeben und da sieht man, dass die Einstellung in mm ist. Wenn ich dann ein Licht einfüge, kann ich nicht sehen, was das für eine Einheit ist. Deswegen versteh ich nicht, was ich da und wo ich da was nachprüfen kann. Mag sein, ich stell mich blöd an.</p>
<p>Hi Thorsten,</p>
<p>Ich habe DDUNITS eingegeben und da sieht man, dass die Einstellung in mm ist. Wenn ich dann ein Licht einfüge, kann ich nicht sehen, was das für eine Einheit ist. Deswegen versteh ich nicht, was ich da und wo ich da was nachprüfen kann. Mag sein, ich stell mich blöd an.</p> Hi Judith,
soviel ich versteh…tag:accurender.ning.com,2016-09-16:6293855:Comment:1234722016-09-16T16:52:28.355ZThorsten Hedrichhttp://accurender.ning.com/profile/ThorstenHedrich
<p>Hi Judith,</p>
<p>soviel ich verstehe, meint Roy einfach nachzuprüfen, ob die Einheiten, mit denen die</p>
<p>Lichtquellen eingefügt werden (mm,cm,m,inches...) auch den verwendeten Einheiten in Deiner AutoCad Zeichnung entsprechen.</p>
<p>Dazu einfach in der Befehlszeile 'DDUNITS' eingeben.</p>
<p>Die Einheiten müssen übereinstimmen, sonst wirds, je nach dem, zu hell oder zu dunkel.</p>
<p></p>
<p>Ciao, Thorsten</p>
<p></p>
<p>Hi Judith,</p>
<p>soviel ich verstehe, meint Roy einfach nachzuprüfen, ob die Einheiten, mit denen die</p>
<p>Lichtquellen eingefügt werden (mm,cm,m,inches...) auch den verwendeten Einheiten in Deiner AutoCad Zeichnung entsprechen.</p>
<p>Dazu einfach in der Befehlszeile 'DDUNITS' eingeben.</p>
<p>Die Einheiten müssen übereinstimmen, sonst wirds, je nach dem, zu hell oder zu dunkel.</p>
<p></p>
<p>Ciao, Thorsten</p>
<p></p> Hi Roy,
maybe my english isn…tag:accurender.ning.com,2016-09-16:6293855:Comment:1234712016-09-16T12:01:52.122ZJudith Kleinhttp://accurender.ning.com/profile/JudithKlein
<p>Hi Roy,</p>
<p></p>
<p>maybe my english isn´t well enough because I don´t know what you mean with "use the _DDUNITS command. Make sure the insertion scale matches the actual units in your model." </p>
<p>My Settings in ACAD are Millimeter, I always draw in this scale für over 15 years and I work with accurender since 2006, and if there was a prolblem with light, the lights were rather to dark but not to bright. I don´t understand what you mean with the Insertion scale matches and the actual…</p>
<p>Hi Roy,</p>
<p></p>
<p>maybe my english isn´t well enough because I don´t know what you mean with "use the _DDUNITS command. Make sure the insertion scale matches the actual units in your model." </p>
<p>My Settings in ACAD are Millimeter, I always draw in this scale für over 15 years and I work with accurender since 2006, and if there was a prolblem with light, the lights were rather to dark but not to bright. I don´t understand what you mean with the Insertion scale matches and the actual units?</p>
<p>The Problem appears since I install the newest update from nxt. I send you the file. Maybe you what´s wrong.</p>
<p></p>
<p>Thanks, Judith.</p> No, this is not a common prob…tag:accurender.ning.com,2016-09-15:6293855:Comment:1234692016-09-15T15:41:54.310ZRoy Hirshkowitzhttp://accurender.ning.com/profile/RoyHirshkowitz
<p>No, this is not a common problem or behavior. Normally, reducing the the output of all of the lights does not change the picture at all.</p>
<p>If you've tried the steps above and still can't figure it out, send the drawing. I'll take a look. Include steps for how to reproduce.</p>
<p>No, this is not a common problem or behavior. Normally, reducing the the output of all of the lights does not change the picture at all.</p>
<p>If you've tried the steps above and still can't figure it out, send the drawing. I'll take a look. Include steps for how to reproduce.</p> Ich wollte nachfragen, ob es…tag:accurender.ning.com,2016-09-15:6293855:Comment:1238052016-09-15T10:42:52.965ZJudith Kleinhttp://accurender.ning.com/profile/JudithKlein
<p>Ich wollte nachfragen, ob es zu meinem Problem eine Lösung gibt. Ich arbeite immer in Millimetern und so ist auch die Zeichnung eingestellt. Oder kann ich irgendwo spezielle im NXT Render eine Einstellung vornehmen? Ich muss die Lichter auf 0,1 Watt anstatt 100 Watt runter drehen, damit das so aussieht wie es soll. Hat denn nicht noch jemand damit ein Problem ?</p>
<p></p>
<p><span lang="en" xml:lang="en">I want to ask again if there is a solution to my problem . I always work in millimeters…</span></p>
<p>Ich wollte nachfragen, ob es zu meinem Problem eine Lösung gibt. Ich arbeite immer in Millimetern und so ist auch die Zeichnung eingestellt. Oder kann ich irgendwo spezielle im NXT Render eine Einstellung vornehmen? Ich muss die Lichter auf 0,1 Watt anstatt 100 Watt runter drehen, damit das so aussieht wie es soll. Hat denn nicht noch jemand damit ein Problem ?</p>
<p></p>
<p><span lang="en" xml:lang="en">I want to ask again if there is a solution to my problem . I always work in millimeters and so the settings are in the drawing. Or could I make a setting somewhere special in NXT Render ? I have to turn down the lights to 0.1 watts instead of 100 watts , so it looks as it should . Has not anyone have a problem with that?</span></p> Check the scale of the model-…tag:accurender.ning.com,2016-08-30:6293855:Comment:1234402016-08-30T16:21:24.379ZRoy Hirshkowitzhttp://accurender.ning.com/profile/RoyHirshkowitz
<p>Check the scale of the model-- use the _DDUNITS command. Make sure the insertion scale matches the actual units in your model.</p>
<p>I'll check on the batch stuff when I get a chance-- working on something else right now.</p>
<p>Check the scale of the model-- use the _DDUNITS command. Make sure the insertion scale matches the actual units in your model.</p>
<p>I'll check on the batch stuff when I get a chance-- working on something else right now.</p>