AccuRender nXt

advanced rendering for AutoCAD

Adds support for *.skp files to the Texture Mesh Object.  Performance is a little slow for large files.  Let me know if it works.

See what's new for more info.

Views: 1159

Reply to This

Replies to This Discussion

Thanks Roy. Yes, in fact I think I'm spending too much time in low quality models...

Hi,

I have bee using NXT 1.0.271 since it came out and am a little confused on how to upgrade.

in AR3 and then AR4 I used to down load a upgrade file but don't see that now.

Thank you

Peter Norwood

http://uhaweb.hartford.edu/norwood/

The latest nXt on the download page will work fine with your current license.  Select "Download for use with Purchased License".  Just run the installer after downloading.

Thank you very much.

Could you please tell me if I have a commercial license or an educational license.

I think I had an educational license with AR3 and AR4 but may have a full NXT.

Thanks again

Peter Norwood

You've got a standard nXt license.  Educational licenses have not (to date) been offered for this product.

Thanks much

Hello Roy

 

Is this an unrelated problem when trying to opening a .skp model?

 

"Application failed to start because MSVC100.DLL was not found.  Re-installing my fix the problem."

 

 

Yep, different problem.  Try downloading and installing from here and let me know.  These may refuse to install.

Good morning Roy,

 

I installed the MS visual c++ 2010 and ran the repair for  Net Framework 4 as recommanded from the web for XP-64.

 

No change.  Nxt will ask for an insert location and then display the error.

Any other suggestions other than reinstalling the previous build?

 

The link I gave you was for x86 (32 bit)-- did you install that one or the one for x64?  If so you need to try to install the one for x86.

I did install the one for the X64 bit system.  Will try the 32 bit .

 

Success.  It's all in the numbers.

The model inserted without a hitch, materials and all.  As noted earlier, the material scales will need to be edited at times.  All materials attached to the test model I inserted came in with a scale of 1x1 with the model scaled correctly.

Super programming, Roy.  Great up-grade.

Thanks for the help.

 

RSS

Search

Translate

Latest Activity

Brittany Watson replied to Brittany Watson's discussion Groundcover Issues
"Hi Ben, You were absolutely right! I took over a computer that was previously used for rendering by someone else. The Accurender Plant Editor was on the desktop and used as the primary plant editor, so I assumed it was the only one. Thank you so…"
May 18
Ben Mixson replied to Brittany Watson's discussion Groundcover Issues
"Hi Brittany, I have two different plant editors. The Accurender plant editor that installed with Accurender Studio and the NXT plant editor that installed with NXT for Autocad. Only the NXT for Autocad version lets you open, modify, and save…"
May 14
Brittany Watson posted a discussion

Groundcover Issues

Hello,I am hoping to get some clarity on how to modify and add groundcover. I have searched everywhere on the forum and online to find how to save a plant as .ArGroundcover, but I cannot find anything. I am using AccuRender Plant Editor and once I finish editing the plant that I want to use as a groundcover, I click "save plant as", but all it allows me to save as is .ArTree. I have a deadline to get this render finished, but I cannot for the life of me figure this out. See More
May 14
Roy Hirshkowitz replied to Roy Hirshkowitz's discussion AccuRender Studio
"Thanks, I'll check on the first two.  The third is normal behavior-- data conversion stops when the arstudio data is detected.  There is a command to remove the arstudio data which would allow you to start from scratch-- probably not…"
Apr 19
Peter Milner replied to Roy Hirshkowitz's discussion AccuRender Studio
"Two things don't seem to translate from nXt: Procedural bump and orientation of texture in a material.   Also, if a decal is changed using nXt, Studio continues to display the original decal. Editing the decal in the Studio material pallet…"
Apr 19
Peter Milner replied to Roy Hirshkowitz's discussion AccuRender Studio
"That sorted it - using the Studio camera and then selecting "Get AutoCAD view"."
Apr 19
Roy Hirshkowitz replied to Roy Hirshkowitz's discussion AccuRender Studio
"Interesting.  ArStudio has its own WalkAbout-like feture, it's the little camera button.  If you do it while the preview is running you should see the view changes automatically in the rendering."
Apr 19
Peter Milner replied to Roy Hirshkowitz's discussion AccuRender Studio
"I'm having trouble getting the desired view in Studio. I've tried setting the view in nXt walkabout and then using that to set the AutoCAD view. However, when I render from Studio, it gives me something different (see images below)."
Apr 19

© 2021   Header image courtesy Peter Milner   Powered by

Badges  |  Report an Issue  |  Terms of Service