AccuRender nXt

advanced rendering for AutoCAD

how can I download old AR3 and AR4 files  *Arplant.

I bought full version just now. Still looking for stunning

plants and bushes of old version.

Please anyone send me the link or downloadable files on my registered email.

Views: 196

Attachments:

Reply to This

Replies to This Discussion

Some of the old plants still work well, but many don't. I had a large selection of palms. nXt does not apply the correct trunk radius, so California Fan palms that used to render with a 3' diameter trunk now render with a 8"+/- trunk. editing the "diameter" with nXts edit tool only makes the tree taller.

This is typical with all of my palms. I've actually moved to using textured mesh obj or 3ds files when it calls for close ups or more detail. That attached image show a Cal Fan Palm that used ro have a trunk nearly the same width as the skirt. 

The leaf mapping is off too. 


Bushes and flowers seem to still render as expected. Haven't tested groundcover, but I assume those are fine too.

Still I did not get real reply to my question.. Please tell me How can I down load all plant files of old versions without having old versions on my computers. Do you know any direct link available ???

I'm doing a search on my PC. I think I still have the old exe's to install (3 seperate if I remember correct). If not at home, I have them at work. I'll look Monday. 

in the meantime..

http://www.accustudio.com/exchange/plants/classic-plants

I don't know what in the zip other than an install exe, but I do know you will need to path the director to the mlib (material library) and plib (plant library) and you will need the textures if the installer does not supply them. I assume it does.

I have accusudio_plib7 on my NXT folder

does it has these old plants

please so me how to install plant library

a plib is from AR3/4 as nXt used individual plant files like materials are. If you have the plib then I assume you have the textures that go with it. I think the mlib has the materials for the plants. I think you should have both.

I have my plant libraries and material folders in one "Materials" folder and have nXt pathed to it (image below). 

Check the little hammer and wrench in the upper right corner of the nXt toolbar. verify the paths are pointing to your folder(s).

Once you check that, you should be able to "add legacy plant" and navigate to your plib.

oh, and I did not have the installers for the plants2 library at home. 90% sure I still have them at work. 

RSS

Search

Translate

Latest Activity

Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"I see that if I turn the soffit layer off, that those can lights on the right are working. So I assume the soffit is blocking the light. Unfortunately, I'm not able to try moving the can lights down for some reason. I can try looking into this…"
23 hours ago
Brittany Watson replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"I apologize, they are the smaller can lights on right soffit side of the arched ceiling, the bigger ones on the opposite side (left) are working correctly. They do work when the light source is pulled out of the can object or out of the soffit, so…"
yesterday
Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Unfortunately, the model was still just too large for my machine. After about 15 minutes I had to turn off the computer so that I could do something else while it was rendering.. Could you give me any idea of where the lights are that don't…"
yesterday
Brittany Watson replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Just sent. Thank you for the quick response!"
yesterday
Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Can you send us a model where this is happening, to see if we can duplicate it here? As small a model as possible would be appreciated. You can use this link to send it to us: https://renderplus.com/wp2/uploads/ Thanks, Rich"
Wednesday
Brittany Watson posted a discussion

Continuous Recessed Lighting Issues

Hi I use AutoCAD Architecture and have been having on going problems with a recessed can light block. I have completed 3 renderings now in which I have had to spend days trying to get my recessed lighting to work. Other lights work, and occasionally some of the can recessed lights will show up. I have exploded the block and added them individually, I have aimed the light and rotated it every which way, but most of the time nothing works.  I have tested out the problem on my current rendering…See More
Wednesday
Roy Hirshkowitz replied to Peter Milner's discussion Accurender Studio cloud rendering
"I pulled the option to use my Azure Batch cloud out of the current product.  There wasn't much interest in it.  You can set up your own Azure account with Microsoft and use it, it's not trivial but also not too hard.  I…"
Feb 21
Peter Milner posted a discussion

Accurender Studio cloud rendering

How much does it cost to use cloud rendering?See More
Feb 21

© 2020   Header image courtesy Peter Milner   Powered by

Badges  |  Report an Issue  |  Terms of Service