"Since there is no Ambient Occlusion Slot in 'Texture Set' Mode of the nXt-Material Editor,
I found another way around what to do with AO Maps:
Baking it into Diffuse; e.g. Multiplying AO Map over Diffuse/Albedo/Colour in…"
advanced rendering for AutoCAD
Walkabout - Resolution
In walk about when using the "Print" selection under resolution I input in the size of the print I want (30x42) but the image seems to process at a low quality. The image is very grainy. It does not seem to matter how many passes I let it go the images does not improve. How do I increase the quality of the image in relation to the size of image I am after?
Thanks, Todd
Views: 438
Replies to This Discussion
-
Permalink Reply by akinlolu olugboji on
-
Hope the density was not at 1?
-
Permalink Reply by Todd Dodd on
-
OK, I see, I will give that a try. What effect does density have on this?
Thanks a bunch for your help!
Mario Schipflinger said:You should use numbers of pixel. 10x10 inch will be with adequate resolution of 150 DPI 2.250.000 pixel. It depends how much DPI you need for printing. 40x32 with 150 DPI will be (150x40 x 150x32) = 28.800.000 pixel. you will always get render with resolution of screen i think (i am not sure here, i never tryed), after this you must scale picture down, and than you will get DPI with size as you need.
-
Permalink Reply by Roy Hirshkowitz on
-
Todd-- you need to post an example of what you're getting-- the image file is fine. Render at 29 million pixels is usually a terrible idea, BTW.
-
-
As I am looking at the settings I am confused. There is a "Viewport" option where you can enter total pixels, a "Pixel" option where you can pixels in the "X" and "Y" direction and a "Print" Option where you enter the size of the print you want. If I pick the resolution I want and multiply it by the page size I want as you have suggested, wouldn't I then enter this in the "Pixel" option not the "Print" option? Or am I confusing how the two work?
Mario Schipflinger said:scale down was wrong word, sorry i am german. Just tell your software this TIF must be printed with 150 dpi, no need to scale image ;)
-
-
I figured that 29 Million pixels might be high esspecially for my old dog of a machine. Speaking of which Autocad just crashed and I lost the image, I will try to recreate and post it for comment. Thanks, Todd
Roy Hirshkowitz said:Todd-- you need to post an example of what you're getting-- the image file is fine. Render at 29 million pixels is usually a terrible idea, BTW.
Search
Translate
Latest Activity
V1x copy
"The wooden texture of the TV-Console looks quite decent.
The Wallpaper on the left has an interesting structure, maybe it would look even better, if you make the texture seamless + applying a little bit of depth, e. g. with highpass - filter in PS?"
"Thank you for help on this topic!
Will test 'Automesher LT' (developed by Automapki), if I run into troubles again.
[Sometimes I was wondering about, if this forum is still alive... .]"
"Good day,
I searched the former forum posts and found another option to solve this problem which is another plugin to autocad-----AUTOMAPKI. You can give it a try."
Thallasso_Pre_Study_2_50mm
3ds +obj import works for older files-'xfrog-plants', for instance... .Comments + Critics appreciated!Hopefully accurender still survives!
"Found 'Textured Mesh Support' only works with obj and 3ds Files which do not contain PBR Maps.
To 'obj' converted newer 3ds do not render in nXt :-("
© 2026 Header image courtesy Peter Milner
Powered by
