AccuRender nXt

advanced rendering for AutoCAD

Any time I launch AutoCad 2014 64bit on Win10. I get this error.

Nxt still works when I type, "nxt" into the command prompt.

Why and how can I remove it?

Views: 236

Reply to This

Replies to This Discussion

I have AutoCad 2010 64bit and 2007 32 bit on the same pc but those do not launch this error splash.

If you comfortable using Regedit to open the registry, can you send me an export of the HKEY_LOCAL_MACHINE section of your registry?

I can take a look at that export file and see if there is an entry for AutoCad 2010 to run "AccuRender nXt.arx".

Let me know if you need help exporting  a section of the registry.

You can use this link to send us a large file:

The splash screen only comes up on AutoCad 2014.

I just click ok and it is gone. 

When I need nxt I just type at the command prompt to launch nxt. 

You are right about 350MB still uploading.

I'll take a look at the file when it gets here.

Meanwhile, I should have asked you this first, have you looked in the StartUp Suite to make sure that  the module "AccuRender nXt.arx" was not listed there?

Also, have you looked to see if there was a file "acad.rx" in The AutoCAD 2014 program Files folder that might have "AccuRender nXt.arx" listed as a module to load?


Unless am doing something wrong the file is only 2KB


That just shows the entry for the AutoCAD 2014. That looks OK.

To export a .reg file with all the HKEY_LOCAL_MACHINE section included, select the section, as shown below, and then export a file. Then I can search the huge file it creates and see if anything besides the AutoCAD 2007 entries point to "AccuRender nXt.arx". You can also do that yourself,  by searching the whole registry for "AccuRender nXt.arx".

Here is a screen shot


The only reference to loading the module "AccuRender nXt.arx" in the registry file that you sent me was for AutoCAD 2007, R17.0:

"LOADER"="C:\\Program Files\\AccuRender nXt\\AccuRender nXt.arx"

So I would then suspect that "AccuRender nXt.arx" is listed either in the StatUp Suite, or in an acad.rx file in the AutoCAd 2014 Program files folder. try looking in those places.





Latest Activity

Rich Hart replied to Paul Jackson's discussion Bricscad
"Unfortunately, we don't have a version that works with BricsCAD now, and that older trial version cannot be reinstated."
Jun 19
Alfons Akamp replied to Paul Jackson's discussion Bricscad
"Ich habe hier auch eine nxtrender Version für Bricscad 15. Die sieht anders aus, als die von Acad. Leider ist auch bei mir der Testzeitraum schon lange abgelaufen. Gibt es die Möglichkeit mir eine Testlizenz dafür zuzuschicken??…"
Jun 19
George Ioannidis commented on Chris Fox's photo


"Another good rendering. Those two photoshopped reading lights are not looking good though. They don't follow the perspective, the left one is higher than the right one. Also, they are supposed to be turned on (judging from the light on wall…"
Jun 15
George Ioannidis commented on Chris Fox's photo

Single Family Home

"Great image as always. I would just blur the tree shadow on the lawn to match soft shadows on the building. Nice blending of cut-out greenery. Excellent job."
Jun 15
George Ioannidis commented on Chris Fox's photo

Railroad kitchen

"Very nice rendering Chris! The only thing that distracts me is the fruit bowl. It's too evidently pasted in PS.  Another thing (nothing to do with rendering) is the microwave above the stove. I would rather expect a cooker hood there."
Jun 15
akinlolu olugboji posted a discussion

trim and extension command

On AutoCad 2021.The trim and extension command works funny. I initiate the command then click the cutting edge (press entre) then click the lines I need to trim or extend.Now I initiate the command and as soon as I click the object selected trims or extend.  How can I correct this, it is really affecting my work?See More
Jun 14
Chris Fox posted photos
Jun 12
ebenezer attah koomson posted photos
Jun 3

© 2020   Header image courtesy Peter Milner   Powered by

Badges  |  Report an Issue  |  Terms of Service