AccuRender nXt

advanced rendering for AutoCAD

why I cant use accurender version 1.0.354 in autocad 2018

Views: 167

Reply to This

Replies to This Discussion

Normally, nXtRender registers its commands with AutoCAD during installation. On occasion, this mechanism may fail. In this case you will need to manually load nXt the first time you run it in a particular version of AutoCAD.

 

Use the following procedure:

  1. Type _appload at the command line.
  2. Navigate to the folder where nXt was installed. This is normally C:\Program Files\AccuRender nXt
  3. Select one of the following files depending on your platform:
  • AccuRender nXt.arx -OR- AccuRender nXt64.arx (AutoCAD 2007 – 2009)
  • AccuRender nXt_18_.arx -OR- AccuRender nXt_18_64.arx (AutoCAD 2010 – 2012)
  • AccuRender nXt_19_.arx -OR- AccuRender nXt_19_64.arx (AutoCAD 2013 – 2014)
  • AccuRender nXt_20_.arx -OR- AccuRender nXt_20_64.arx (AutoCAD 2015 - 2016)
  • AccuRender nXt_21_.arx -OR- AccuRender nXt_21_64.arx (AutoCAD 2017)
  • AccuRender nXt_22_.arx -OR- AccuRender nXt_22_64.arx (AutoCAD 2018)
  • AccuRender nXt_23_.arx -OR- AccuRender nXt_23_64.arx (AutoCAD 2019 - 2020)

 

          Press Load

 

For example, you should be able to load the one named AccuRender nXt_22_64.arx for AutoCAD 2018 or AutoCAD Architecture 2018, on a 64 bit computer.

 

Check the AutoCAD command line to verify that the application loaded without error. At this point you should be able to type nxt or ar5 to launch the application. You should not have to repeat this procedure again for this version of AutoCAD. Simply typing nxt or ar5 at the command prompt should cause nxt to load. You may need to repeat this procedure if you install another version of AutoCAD.

 

NO 22

...

ok...

the RPS_nXtRender_R22_x64 sudenly is there... magic..!!

thanks HART.... I JUST DOMLOAD AGAIN AND REBOOT...

RSS

Search

Translate

Latest Activity

Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"I see that if I turn the soffit layer off, that those can lights on the right are working. So I assume the soffit is blocking the light. Unfortunately, I'm not able to try moving the can lights down for some reason. I can try looking into this…"
yesterday
Brittany Watson replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"I apologize, they are the smaller can lights on right soffit side of the arched ceiling, the bigger ones on the opposite side (left) are working correctly. They do work when the light source is pulled out of the can object or out of the soffit, so…"
yesterday
Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Unfortunately, the model was still just too large for my machine. After about 15 minutes I had to turn off the computer so that I could do something else while it was rendering.. Could you give me any idea of where the lights are that don't…"
yesterday
Brittany Watson replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Just sent. Thank you for the quick response!"
yesterday
Rich Hart replied to Brittany Watson's discussion Continuous Recessed Lighting Issues
"Can you send us a model where this is happening, to see if we can duplicate it here? As small a model as possible would be appreciated. You can use this link to send it to us: https://renderplus.com/wp2/uploads/ Thanks, Rich"
Wednesday
Brittany Watson posted a discussion

Continuous Recessed Lighting Issues

Hi I use AutoCAD Architecture and have been having on going problems with a recessed can light block. I have completed 3 renderings now in which I have had to spend days trying to get my recessed lighting to work. Other lights work, and occasionally some of the can recessed lights will show up. I have exploded the block and added them individually, I have aimed the light and rotated it every which way, but most of the time nothing works.  I have tested out the problem on my current rendering…See More
Wednesday
Roy Hirshkowitz replied to Peter Milner's discussion Accurender Studio cloud rendering
"I pulled the option to use my Azure Batch cloud out of the current product.  There wasn't much interest in it.  You can set up your own Azure account with Microsoft and use it, it's not trivial but also not too hard.  I…"
Feb 21
Peter Milner posted a discussion

Accurender Studio cloud rendering

How much does it cost to use cloud rendering?See More
Feb 21

© 2020   Header image courtesy Peter Milner   Powered by

Badges  |  Report an Issue  |  Terms of Service