AccuRender nXt

advanced rendering for AutoCAD

Are there new .ARX files etc needed to get nXt rendering running inside Acad 2019 I've tried loading the files that worked for Acad 2016 but when I type 'nxt' on the Acad command line it says not recognized.

Many thanks

Diz

Views: 948

Reply to This

Replies to This Discussion

Download and install the latest version from:

nXtRender Downloads Page

Normally nXtRender registers its commands with AutoCAD during installation. On occasion, this mechanism may fail. In this case you will need to manually load nXt the first time you run it in a particular version of AutoCAD. Use the following procedure:

  1. Type _appload at the command line.
  2. Navigate to the folder where nXt was installed. This is normally C:\Program Files\AccuRender nXt
  3. Select one of the following files depending on your platform:
  • AccuRender nXt.arx-OR- AccuRender nXt64.arx (AutoCAD 2007 – 2009)
  • AccuRender nXt_18_.arx-OR- AccuRender nXt_18_64.arx (AutoCAD 2010 – 2012)
  • AccuRender nXt_19_.arx-OR- AccuRender nXt_19_64.arx (AutoCAD 2013 – 2014)
  • AccuRender nXt_20_.arx-OR- AccuRender nXt_20_64.arx (AutoCAD 2015- 2016)
  • AccuRender nXt_21_.arx -OR- AccuRender nXt_21_64.arx(AutoCAD 2017)
  • AccuRender nXt_22_.arx -OR- AccuRender nXt_22_64.arx(AutoCAD 2018)
  • AccuRender nXt_23_.arx -OR- AccuRender nXt_23_64.arx(AutoCAD 2019)
  1. Press Load

Check the AutoCAD command line to verify that the application loaded without error. At this point you should be able to type nxt or ar5 to launch the application. You should not have to repeat this procedure again for this version of AutoCAD. Simply typing nxt or ar5 at the command prompt should cause nxt to load. You may need to repeat this procedure if you install another version of AutoCAD.

Regards,

Rich

Hey Rich,

Fantastic stuff, right on the money, worked like a charm.

Thanks so much.

Diz

RSS

Search

Translate

Latest Activity

Rich Hart replied to Paul Jackson's discussion Bricscad
"Unfortunately, we don't have a version that works with BricsCAD now, and that older trial version cannot be reinstated."
Jun 19
Alfons Akamp replied to Paul Jackson's discussion Bricscad
"Ich habe hier auch eine nxtrender Version für Bricscad 15. Die sieht anders aus, als die von Acad. Leider ist auch bei mir der Testzeitraum schon lange abgelaufen. Gibt es die Möglichkeit mir eine Testlizenz dafür zuzuschicken??…"
Jun 19
George Ioannidis commented on Chris Fox's photo
Thumbnail

Bedroom

"Another good rendering. Those two photoshopped reading lights are not looking good though. They don't follow the perspective, the left one is higher than the right one. Also, they are supposed to be turned on (judging from the light on wall…"
Jun 15
George Ioannidis commented on Chris Fox's photo
Thumbnail

Single Family Home

"Great image as always. I would just blur the tree shadow on the lawn to match soft shadows on the building. Nice blending of cut-out greenery. Excellent job."
Jun 15
George Ioannidis commented on Chris Fox's photo
Thumbnail

Railroad kitchen

"Very nice rendering Chris! The only thing that distracts me is the fruit bowl. It's too evidently pasted in PS.  Another thing (nothing to do with rendering) is the microwave above the stove. I would rather expect a cooker hood there."
Jun 15
akinlolu olugboji posted a discussion

trim and extension command

On AutoCad 2021.The trim and extension command works funny. I initiate the command then click the cutting edge (press entre) then click the lines I need to trim or extend.Now I initiate the command and as soon as I click the object selected trims or extend.  How can I correct this, it is really affecting my work?See More
Jun 14
Chris Fox posted photos
Jun 12
ebenezer attah koomson posted photos
Jun 3

© 2020   Header image courtesy Peter Milner   Powered by

Badges  |  Report an Issue  |  Terms of Service